Construction Technology 6.01

What safety device is used to push materials to protect fingers from jointer knives?
1. Block of wood
2. Push block/stick
3. Slider
4. Sticker
The safety-grounded electrical cord has a MINIMUM of how many wires?
1. One
2. Two
3. Three
4. Four
The FIRST step in making adjustments to power tools is to:
1. Disconnect the power source.
2. Insert the shank.
3. Lock the shaft.
4. Tighten the chuck.
How fine a saw blade cuts depends upon the:
1. Arbor size.
2. Carbide teeth.
3. High speed steel.
4. Number of teeth.
What saw is used to make smooth curved finish cuts in wood?
1. Circular or skill
2. Reciprocating or sawzall
3. Sabre or jigsaw
4. Table or bench
What saw is MOST useful for demolition work on a re-modeling job?
1. Radial
2. Reciprocating
3. Sabre
4. Table
Circular power saws should be operated on what amperage electrical circuit?
1. 5
2. 10
3. 15
4. 20
Radial arm saws are sized according to the:
1. Blade diameter.
2. Motor HP.
3. Table size.
4. Voltage.
MOST portable circular saws will make bevel cuts up to:
1. 15°.
2. 15°.
3. 45°.
4. 60°.
What is the MOST popular size circular saw blade?
1. 10"
2. 8"
3. 7-1/2 "
4. 7-1/4"
What is the MOST popular shape of portable drills?
1. Offset
2. Pistol grip
3. Stationary
4. Straight
A portable circular saw has:
1. A fixed (non-adjustable) baseplate.
2. A retractable lower blade guard.
3. A retractable upper blade guard.
4. Retractable lower and upper blade guards.
The portable belt sander is designed for:
1. Removing rust and scale.
2. Sanding metal.
3. Sanding plastic.
4. Sanding wood.
Setting anchors and drilling holes in masonry and concrete is normally done using a portable:
1. Chipping hammer.
2. Hammer drill.
3. Power sledgehammer.
4. Screw gun.
A pneumatic stapler is used to install:
1. Exterior doors.
2. Insulation.
3. Roofing shingles.
4. Sheathing.
What power tool is shown below?
1. Angle grinder
2. Bench grinder
3. End grinder
4. Portable drill
What power tool is shown below?
1. Angle grinder
2. Bench grinder
3. End grinder
4. Portable drill
Which is a stationary grinding machine?
1. Angle grinder
2. Bench grinder
3. Drill press
4. End grinder
The smooth portion of a drill bit that fits into the chuck is the:
1. Handle.
2. Key.
3. Key.
4. Tang.
The pneumatic drill is powered by:
1. Compressed air.
2. Compressed gas.
3. Compressed water.
4. Gunpowder.
What power drill is powered by air?
1. Cordless
2. Cordless
3. Hydraulic
4. Pneumatic
The purpose of the chuck key on a power drill is to:
1. Lock the chuck on the drill so that it will not get lost.
2. Lock the drill in the case so no one can steal it.
3. Set the drill speed and keep it constant.
4. Tighten the jaws of the chuck on the drill bit.
What power tool is shown below?
1. Cordless drill
2. Electro-magnetic drill
3. Hammer drill
4. Hammer drill
What power tool is shown below?
1. Electro-magnetic drill
2. Hammer drill
3. Jack hammer
4. Reciprocating saw

Construction Technology 6.01

Quiz